When you search for masonry contractors near me Milwaukie OR, you want a crew that shows up, knows Oregon code, and fixes the problem for good. RenovoBase has served Milwaukie homeowners and businesses since 2021, handling crumbling brickwork, chimney leaks, spalling brick, and settling walls. We work with brick, stone, concrete block, and natural stone veneer, and we give you an upfront price before we start. Call (855) 947-9500 for a same-day estimate.
Tell us what is happening. Our local team will confirm your visit shortly.
Call Now (855) 947-9500 → No spam. No obligation. Just practical help.
masonry contractors near me Milwaukie OR is a licensed trade that repairs, rebuilds, and installs brick, stone, concrete block, and mortar structures so they stay watertight and structurally sound. That covers everything from repointing a crumbling chimney to laying a new stone veneer wall. We mix mortar to match the existing color and hardness, set reinforcing steel where the wall needs it, and tie new work into old so the joint doesn't crack next winter. Most of our Milwaukie calls start with water getting in where it shouldn't.
Milwaukie's wet winters and freeze-thaw cycles punish masonry. Water soaks into brick, freezes overnight, and pops the face off - that's spalling brick, and it only gets worse. Older homes near Downtown Milwaukie and Hector Campbell often have original mortar that has gone soft, so the joints crumble and the wall starts to settle. If you've been looking for local masonry contractors near me Milwaukie Oregon, we handle the whole repair: diagnose the water path, fix the flashing or drainage, then rebuild the masonry so it drains correctly.
Every job starts with a site inspection and a written scope. What's included depends on the repair, but here's what you can count on from a standard masonry call.
A mason walks the property, taps brick for hollow spots, checks flashing and weep holes, and probes mortar joints. You get photos, measurements, and a written scope with a fixed price before any work begins.
We sample your existing brick, stone, and mortar and match color, texture, and hardness. For older Milwaukie homes that means lime mortar, not portland cement. We confirm the match with you before ordering.
Failed mortar is cut out with an angle grinder and trowel, spalled brick is replaced, flashing and weep holes are installed or repaired, and the wall is repointed or rebuilt to IBC and ASTM standards.
We apply breathable silane or siloxane sealer to stop water infiltration without trapping moisture. Weep holes are cleaned and flashing is checked. Resealing is recommended every 5 to 7 years in Milwaukie's wet climate.
We haul off all debris, wash down the work area, and walk the job with you. You get a written 5-year workmanship warranty and maintenance notes - usually a reminder to check the chimney crown each fall.
Call (855) 947-9500 or book online. We ask what you're seeing - crumbling brick, a chimney leak, a wall that's leaning - and schedule a site visit, usually within 24 to 48 hours. For active leaks or storm damage, we offer 24/7 emergency response and can tarp or brace the area the same day.
A mason walks the property with you, taps the brick with a hammer to check for hollow spots, checks the flashing and weep holes, and probes the mortar joints with a chisel. We take photos and measurements. You get a written scope and a fixed price before any work begins - no surprise change orders.
We pull samples of your existing brick, stone, and mortar and match them. For older Milwaukie homes, that often means a lime mortar mix rather than portland cement, because hard mortar traps moisture and cracks soft historic brick. We confirm the match with you before ordering.
The crew cuts out failed mortar with an angle grinder and trowel, replaces spalled brick, installs new flashing and weep holes, and repoints or rebuilds the wall. A typical chimney repoint takes one to two days; a foundation repair or stone veneer install runs three to seven days depending on square footage.
We haul off debris, wash down the work area, and walk the job with you. You get a written warranty and maintenance notes - usually a reminder to check the chimney crown each fall and keep sprinklers from spraying the brick. Final payment is due only after you've signed off.
Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.
Used to spread mortar, set brick, and check that every course is plumb and level. A wall that's out of level by 1/8 inch over 10 feet will show at the roofline.
Cuts out failed mortar joints and cuts brick or stone to size. The wet saw keeps dust down and gives a clean cut on stone veneer and cast stone.
Used to remove spalled brick and shape replacement units. A brick hammer breaks cleanly along the grain, which matters when you're matching historic brick.
Mixes mortar to the right consistency and hardness. We mix lime mortar for pre-1950 Milwaukie brick and portland cement mixes for modern block.
The line keeps courses straight over long walls; the jointing tool finishes the mortar joint to the right profile so it sheds water instead of holding it.
Bagged mortar mixes we use for repairs and small pours. We match the mix to the existing wall - type N or O for soft historic brick, type S for structural block.
The chimney had 30 feet of crumbling mortar joints, a failed crown, and water staining on the attic ceiling. Two other bids recommended a full rebuild at $6,500 or more.
We replaced the crown, repaired the flashing, and repointed 30 feet of joints with lime mortar matched to the original. Total cost was $1,180 and the job took two days. The attic has been dry through two winters.
A January windstorm knocked down 20 feet of a block retaining wall. The wall had no drainage and the soil behind it was saturated. The homeowner called at 9 p.m. during the storm.
We braced the remaining wall the next morning and rebuilt the 20-foot section in four days with geogrid, reinforcing steel, and a gravel drainage column. The Clackamas County permit was included. Final cost was $4,800.
A 1980s home had faded T1-11 siding on the front elevation. The homeowner wanted stone veneer but two bids came in over $18,000 with no drainage detail.
We installed 420 square feet of natural stone veneer over a new drainage plane with flashing and weep holes. The job took six days and cost $11,400. The wall drains correctly and the veneer carries our 5-year workmanship warranty.
Most masonry calls come down to water, movement, or age. Here are the problems we see most often and how we fix them.
Ask a pro →We cut out the failed mortar with an angle grinder and trowel, match the original mix - lime mortar on pre-1950 Milwaukie homes - and repoint the joints. We also fix the water source, usually flashing or a clogged weep hole, so the repair lasts.
We diagnose the water path first, then repair the crown, flashing, or joints. Most chimney repairs run $400 to $1,800 and take one to two days. We tarp active leaks the same day and offer 24/7 emergency response.
We replace spalled brick with a matched replacement from Glen-Gery or Mutual Materials, repoint the surrounding joints, and apply a breathable sealer. We also correct the drainage or flashing that caused the moisture in the first place.
We address the water source, then rebuild the wall with reinforcing steel and proper drainage. Foundation masonry repairs typically run $2,500 to $9,000 depending on the length and depth of the repair.
Start by checking the Oregon CCB License and asking for proof of insurance and bonding. Then ask for two or three local references and photos of recent work. We provide all of that upfront, plus a written scope and fixed price before work begins. Call (855) 947-9500 and we'll schedule a same-day or next-day site visit.
Yes. Chimney leaks are one of our most common calls in Milwaukie. The fix usually starts with the crown, flashing, or a failed mortar joint - not the whole chimney. We diagnose the water path first, then repair the masonry. Most chimney repairs run $400 to $1,800 depending on scope, and we can tarp an active leak the same day.
Look for a crew that uses lime mortar on pre-1950 brick, not portland cement. Hard mortar traps moisture and cracks soft historic brick. We match mortar hardness, color, and aggregate to the original wall, and we source replacement brick from Glen-Gery and Mutual Materials. That's the difference between a repair that lasts and one that spalls in two winters.
Typical 2026 pricing in this area runs $400 to $1,800 for chimney and repoint work, $2,500 to $9,000 for retaining walls, and $12 to $30 per square foot for stone veneer. Cost drivers are access, height, how much brick needs replacing, and whether the wall needs structural reinforcement. We give you a fixed price before we start.
brick masonry contractorNew brick walls, columns, and repairs built to IBC and ASTM Masonry Standards. We match existing brick from Glen-Gery and Boral so additions blend with the original structure. Common for Milwaukie homeowners adding a porch column or rebuilding a damaged wall section.Explore →
chimney masonry near meChimney repointing, crown repair, flashing replacement, and full rebuilds. Milwaukie's wet winters find every failed joint, so we fix the water path first and rebuild the masonry second. Most chimney jobs take one to two days and carry our 5-year workmanship warranty.Explore →
masonry fireplace contractors near meInterior and exterior fireplace builds, firebox repairs, and chimney tie-ins. We set firebrick, cast stone surrounds, and hearths that meet code and handle heat cycling. Popular in Milwaukie Heights and Concord homes upgrading from a builder-grade insert.Explore →
masonry restorationFull restoration for historic and damaged masonry - repointing, brick replacement, structural reinforcement, and waterproofing. We work on pre-1950 Milwaukie homes with lime mortar and soft brick, matching color and hardness so the repair doesn't damage the original wall.Explore →
stone masonry contractorNatural stone veneer, cast stone, and full stone walls. We source regional stone and set it with proper flashing and weep holes so water drains instead of sitting behind the wall. Common on Milwaukie Riverfront homes and Island Station remodels.Explore →
emergency masonry repair24/7 response for chimney leaks, cracked walls, and storm damage. We tarp, brace, or shore up the structure the same night, then return for the permanent repair. Call (855) 947-9500 any hour - we've handled January windstorm damage across Clackamas County.Explore →
24/7 masonry contractorRound-the-clock availability for active leaks, fallen brick, and structural emergencies. A real mason answers, not a call center. We dispatch from Milwaukie and can usually reach most Clackamas County addresses within 60 to 90 minutes for urgent calls.Explore →
stone wall contractorFree-standing and retaining stone walls built with proper drainage, reinforcing steel, and compacted base. We size the wall to the load and pull permits when required. Typical Milwaukie retaining wall runs $2,500 to $9,000 depending on height and length.Explore →Licensed, insured, and backed by a 5-year workmanship warranty. Same-day estimates, 24/7 emergency response, and fixed pricing before we start. Call (855) 947-9500 or book online - we'll schedule a site visit within 24 to 48 hours.
Get a Free Estimate (855) 947-9500 →Call (855) 947-9500 or email info@renovobase.com and we will get back to you within one business day. For emergencies, the 24/7 line is always open. We schedule estimates Monday through Friday and can usually be on site the same day you call.