We handle brick repair services Milwaukie OR homeowners call about most: spalling faces, cracked mortar joints, chimney leaks, and brick veneer pulling away from the wall. Our crews work Clackamas County addresses daily, from 97222 bungalows to riverfront commercial buildings. If water is getting into your masonry, we find where and fix it before the freeze cycle makes it worse.
Tell us what is happening. Our local team will confirm your visit shortly.
Call Now (855) 947-9500 → No spam. No obligation. Just practical help.
Brick repair services Milwaukie OR is the trade of cutting out failed brick and mortar and rebuilding the wall so water stays outside. That means grinding out deteriorated mortar joints to the right depth, matching the original mix, and replacing spalled units with brick that meets ASTM Masonry Standards for absorption and compressive strength. We repoint, rebuild, and waterproof. We do not smear a coat of caulk over a cracked foundation and call it done.
Milwaukie brick takes a beating. Rain saturates the wall from October through May, then a hard freeze cracks whatever the water got into. Older homes around Hector Campbell and Ardenwald were built with lime mortar that turns to sand after 70 or 80 years, and that is when brick repair in Milwaukie OR stops being cosmetic. Efflorescence, spalling brick, and mortar joint deterioration all point to the same problem: water is moving through the wall. We fix the source, not the symptom.
Every brick repair job we quote includes inspection, prep, materials, labor, and cleanup. What changes is the scope: a repoint is not a rebuild, and a rebuild is not a foundation repair. Here is what is covered on a standard repair, and what we quote separately when the wall needs more.
We tap-test the wall, check mortar joints with a chisel, and photograph every problem area. You get a written scope with line-item pricing, usually the same day as the inspection. No charge for the estimate.
Failed mortar gets ground out to a 3/4-inch depth with an angle grinder and tuck-pointing blade. Spalled brick comes out with a brick hammer and chisel. Landscaping gets covered before any cutting starts.
We replace spalled and cracked units with brick matched for size, color, and absorption. Brands like Glen-Gery, Boral, and Mutual Materials cover most Milwaukie homes. Matching brick on a 1920s wall sometimes means sourcing salvaged units.
New mortar gets packed into the joints and finished with a jointing tool to match the original profile. We use lime mortar on historic masonry and portland cement blends on modern brick. The joint profile matters as much as the mix.
If water is getting in at a roof-to-wall transition or a chimney, we repair or replace the flashing. Repointing a wall without fixing the flashing just moves the leak. Weep points and drainage get checked on every job.
We broom-clean the site, haul away debris, and walk the finished work with you. You get a written workmanship warranty and instructions on when to schedule waterproofing if the mortar still needs to cure.
We walk the wall with you, tap-test for hollow brick, and check mortar joints with a mason's level and chisel. You get photos of every problem area and a written scope the same day. Most inspections take 45 minutes to an hour.
You get line-item pricing: brick replacement, repointing, flashing, waterproofing, and any structural work. No lump-sum guesswork. If a cracked foundation needs a structural engineer, we tell you before we quote, not after.
We grind out failed mortar with an angle grinder and tuck-pointing blade, remove spalled brick with a brick hammer and chisel, and protect landscaping with drop cloths. Prep is 30 to 40 percent of the job, and skipping it is why cheap repairs fail.
New brick goes in with a mason's line for alignment, then joints get packed with mortar and finished with a jointing tool. We match the original joint profile, whether that is concave, V, or grapevine, so the repair disappears into the wall.
We apply a breathable masonry waterproofing once mortar cures, usually 3 to 7 days later. Then we walk the finished work with you, point out what to watch, and leave the site broom-clean. Final walkthrough takes about 20 minutes.
Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.
Cuts failed mortar out of joints to a consistent 3/4-inch depth without chipping the brick edges. The depth matters: too shallow and the new mortar pops out within a year.
Removes spalled and cracked brick units without damaging the surrounding wall. We cut the mortar around the unit first, then lift it out clean.
Keeps new brick plumb and courses level during rebuilds. A wall that is out of level by 1/8 inch over 10 feet will show it from across the street.
Finishes the mortar joint to match the original profile, whether concave, V, or grapevine. The profile controls how water sheds off the wall.
Blends mortar to a consistent color and workability. We mix small batches so the mortar does not set up before it is packed into the joints.
Cuts replacement brick and stone to exact dimensions for arches, corners, and custom fits. Dry cutting dust is a health hazard and leaves a rougher edge.
Carries multiple brick units safely up ladders and scaffolding. Chimney work means a lot of trips up and down, and tongs cut the risk of drops.
The south wall had 340 square feet of mortar turning to sand, with 18 spalled brick units and efflorescence staining the whole face. The homeowner had been told the wall needed a full rebuild.
We ground out the failed joints, replaced the 18 brick units with matching salvaged brick, and repointed with a lime mix matched to the original. The wall is uniform again and has survived two winters with no new spalling.
The chimney crown was cracked in three places and the flashing had pulled away from the roof. Every heavy rain sent water down the flue and into the attic, staining the ceiling below.
We rebuilt the crown, repointed the stack, and replaced the flashing in two days. A water test confirmed the leak was gone. The attic stayed dry through the next rainy season.
A 40-foot section of brick veneer above a storefront had detached from the wall. The ties had rusted through and the drainage plane was blocked, so water had been sitting behind the veneer for years.
We removed the loose veneer, repaired the drainage plane and flashing, and reinstalled with new corrosion-resistant ties. The work was done after hours so the storefront never closed. The wall passed inspection on the first pass.
Most brick damage in Milwaukie starts small and gets expensive fast. Water gets in, freezes, and pops the brick face off. Here are the problems we see most often and what happens if you leave them alone.
Ask a pro →We grind out the failed mortar, match a new lime mix to the original, and repoint the wall. Most repoints run 3 to 6 days depending on square footage. The wall stops absorbing water and the brick stops spalling.
We replace spalled units with matching brick, repoint the surrounding joints, and apply breathable waterproofing after the mortar cures. Replacing brick early is far cheaper than rebuilding a wall later.
We rebuild the crown, repoint the stack, and replace the flashing. Most chimney repairs take 1 to 2 days. We test with water before we leave to confirm the leak is actually gone.
We remove the loose veneer, repair the drainage plane and flashing, and reinstall with new corrosion-resistant ties. Skipping the drainage fix guarantees the veneer fails again within a few years.
Most residential brick repair jobs in Milwaukie run $450 to $3,800 in 2026, depending on scope. A single chimney repoint averages $850 to $1,600. Spot brick replacement runs $35 to $70 per brick installed. Full veneer rebuilds start around $18 per square foot. We give you a line-item estimate before any work starts, so the number you hear is the number you pay.
RenovoBase does, and we are based right here in Clackamas County. We cover every Milwaukie ZIP, including 97222 and 97269, plus North Clackamas, Linwood, and Concord. Call (855) 947-9500 and we will schedule an on-site inspection, usually within 48 hours. You get photos, a written scope, and a fixed price before we pick up a trowel.
Yes, and it depends on the crack. Hairline cracks in the brick face usually mean the mortar is failing, not the brick, so we repoint and the crack stops moving. Cracks wider than 1/4 inch or stair-step patterns through the mortar often point to settling or a cracked foundation. We diagnose the cause first, because patching a crack that is still moving wastes your money.
A chimney repoint takes 1 to 2 days. Spot brick replacement on a wall runs 2 to 4 days. A full veneer rebuild on a house takes 1 to 3 weeks, weather depending. Mortar needs 3 to 7 days to cure before we apply waterproofing, so plan on the wall being off-limits for about a week after the last joint is tooled.
brick masonry contractorNew brick walls, additions, and rebuilds. If your repair turns into a larger scope, the same crew that repoints your wall can lay new brick to match. We work to IBC standards and pull permits when the job needs one.Explore →
masonry contractors near meSearching for masonry contractors near me in Milwaukie usually means you want one crew for everything. We handle brick, stone, block, and veneer under one Oregon CCB license, so you are not juggling three subs on one wall.Explore →
chimney masonry near meChimney leaks and crumbling crowns are our most common winter call. We rebuild crowns, repoint stacks, and install new flashing. Most chimney masonry repairs take 1 to 2 days and stop the leak that has been staining your ceiling.Explore →
masonry fireplace contractors near meFireboxes, hearths, and surrounds take heat-rated brick and firebrick mortar. We rebuild fireboxes that have cracked from years of use and reface surrounds with stone or brick. Every fireplace job gets a smoke test before we call it done.Explore →
masonry restorationFull restoration means bringing a failing wall back to original condition, not just patching the visible damage. We document existing conditions, match historic brick and mortar, and rebuild in phases so the building stays usable during the work.Explore →
stone masonry contractorStone repairs follow the same rules as brick: match the material, match the mortar, manage water. We repair natural stone veneer, cast stone, and stone foundation walls across Milwaukie and Clackamas County.Explore →
emergency masonry repairWhen a chimney starts leaking into a living room or a wall bulges after a storm, we triage same-day. Emergency work usually means temporary shoring or tarping first, then a permanent repair scheduled within the week.Explore →
24/7 masonry contractorOur phone line stays open around the clock for urgent masonry calls. After-hours dispatch covers Milwaukie, North Clackamas, and the surrounding area. You talk to a real person, not a call center, and we tell you honestly whether it can wait until morning.Explore →We inspect, photograph, and price your brick repair in one visit, usually within 48 hours of your call. Licensed, insured, and bonded in Oregon. Call (855) 947-9500 and we will tell you straight what the wall needs.
Schedule Inspection (855) 947-9500 →Call (855) 947-9500 or email info@renovobase.com and we will get back to you within one business day. For emergencies, the 24/7 line is always open. We schedule estimates Monday through Friday and can usually be on site the same day you call.